MSI-Patna Pay Fee NowMSI-Patna
MSI - Patna
Admission Now | Subjects | Classes | Eligibility | Fee-Structure | Site-Map | Available Seats | Exams | Time-Table | Rules | NOTICE BOARD | Attendance | Contact Us
NCERT Class 11 Physics Notes : Waves and Sound : Mandakini Study Institute - Patna
1 / 3
2 / 3
3 / 3

NCERT Class 11 Physics Notes : Waves and Sound

Wave

A wave is a vibratory disturbance in a medium which carries energy from one point to another point without any actual movement of the medium. There are three types of waves

  1. Mechanical Waves Those waves which require a material medium for their propagation, are called mechanical waves, e.g., sound waves, water waves etc.
  2. Electromagnetic Waves Those waves which do not require a material medium for their propagation, are called electromagnetic waves, e.g., light waves, radio waves etc.
  3. Matter Waves These waves are commonly used in modern technology but they are unfamiliar to us. Thses waves are associated with electrons, protons and other fundamental particles.

Nature of Waves

(i) Transverse waves A wave in which the particles of the medium vibrate at right angles to the direction of propagation of wave, is called a transverse wave.

CBSE Class 11 Physics Notes Waves and Sound

These waves travel in the form of crests and troughs.

(ii) Longitudinal waves A wave in which the particles of the medium vibrate in the same direction in which wave is propagating, is called a longitudinal wave.

CBSE Class 11 Physics Notes Waves and Sound

These waves travel in the form of compressions and rarefactions.

Some Important Terms of Wave Motion

  1. (i) Wavelength The distance between two nearest points in a wave which are in the same phase of vibration is called the wavelength (λ).
  2. (ii) Time Period Time taken to complete one vibration is called time period (T).
  3. (iii) Frequency The number of vibrations completed in one second is called frequency of the wave.

    Its SI unit is hertz.
  4. (iv) Velocity of Wave or Wave Velocity The distance travelled by a wave in one second is called velocity of the wave (u).
    Relation among velocity, frequency and wavelength of a wave is given by v = fλ.
  5. (v) Particle Velocity The velocity of the particles executing SHM is called particle velocity.

Sound Waves

Sound waves of all the mechanical waves that occur in nature, the most important in our everyday lives are longitudinal waves in a medium, usually air, called sound waves.

Sound waves are of three types

(i) Infrasonic Waves The sound waves of frequency lies between 0 to 20 Hz are called infrasonic waves.

(ii) Audiable Waves The sound waves of frequency lies between 20 Hz to 20000 Hz are called audiable waves.

 

(iii) Ultrasonic Waves The sound waves of frequency greater than 20000 Hz are called ultrasonic waves.

Sound waves are mechanical longitudinal waves and require medium for their propagation. Sound waves can travel through

[sound waves cannot propagate through vacuum.

If Vs, Vi and Vg are speed of sound waves in solid, liquid and gases, then

Vs > Vi > Vg

Sound waves (longitudinal waves) can reflect, refract, interfere and diffract but cannot be polarised as only transverse waves can polarised.]

Velocity of Longitudinal (Sound) Waves

Velocity of longitudinal (sound) wave in any medium is given by

CBSE Class 11 Physics Notes Waves and Sound

where, E is coefficient of elasticity of the medium and ρ is density of the medium.

Newton’s Formula

According to Newton, the propagation of longitudinal waves in a gas is an isoth. ermal process. Therefore, velocity of longitudinal (sound) waves in gas should be

CBSE Class 11 Physics Notes Waves and Sound

where, ET is the isothermal coefficient of volume elasticity and it is equal to the pressure of the gas.

Laplace’s Correction

According to Laplace, the propagation of longitudinal wave is an adiabatic process. Therefore, velocity of longitudinal (sound) wave in gas should be

CBSE Class 11 Physics Notes Waves and Sound

where, ES, is the adiabatic coefficient of volume elasticity and it is equal to γ p.

Factors Affecting Velocity of Longitudinal (Sound) Wave

 

(i) Effect of Pressure The formula for velocity of sound in a gas.

CBSE Class 11 Physics Notes Waves and Sound

Therefore, (p/ρ) remains constant at constant temperature.

Hence, there is no effect of pressure on velocity of longitudinal wave.

(ii) Effect of Temperature Velocity of longitudinal wave in a gas

CBSE Class 11 Physics Notes Waves and Sound

Velocity of sound in a gas is directly proportional to the square root of its absolute temperature.

CBSE Class 11 Physics Notes Waves and Sound

If v0 and vt are velocities of sound in air at O°C and t°C, then

(iii) Effect of Density The velocity of sound in gaseous medium

CBSE Class 11 Physics Notes Waves and Sound

The velocity of sound in a gas is inversely proportional to the square root of density of the gas.

(iv) Effect of Humidity The velocity of sound increases with increase in humidity in air.

Shock Waves

If speed of a body in air is greater than the speed of sound, then it .s called supersonic speed. Such a body leaves behind it a conical “egion of disturbance which spreads continuously. Such a disturbance is Called a shock wave.

Speed of Transverse Motion

On a stretched string v = √(T/m)

where, T = tension in the string and m = mass per unit length of the string.

Speed of transverse wave in a solid v = √(η/ρ)

where, η is modulus of rigidity and ρ is density of solid.

Plane Progressive Simple Harmonic Wave

Equation of a plane progressive simple harmonic wave

CBSE Class 11 Physics Notes Waves and Sound

where,

  • y = displacement,
  • a = amplitude of vibration
  • λ = wavelength of wave, of particle,
  • T = time period of wave,
  • x = distance of particle from the origin and
  • u = velocity of wave.

Important Relation Related to Equation of Progressive Wave

CBSE Class 11 Physics Notes Waves and Sound

Relation between phase difference and path difference and time difference

CBSE Class 11 Physics Notes Waves and Sound

Echo

The repetition of sound caused by the reflection of sound waves is called an echo.

Sound persists on ear for 0.1 s.

The minimum distance from a sound reflecting surface to hear an echo is 16.5 m.

If first echo be heard after It second, second echo after ~ second, then third echo will be heard after (t1 + t2)s.

Superposition of Waves

Two or more progressive waves can travel simultaneously in the medium without effecting the motion of one another. Therefore, resultant displacement of each particle of the medium at any instant is equal to vector sum of the displacements produced by two waves separately. This principle is called principle of superposition.

Interference

When two waves of same frequency travel in a medium simultaneously in the same direction, then due to their superposition, the resultant intensity at any point of the medium is different from the sum intensities of the two waves. At some points the intensity of the resultant wave is very large while at some other points it is very small Or zero. This phenomenon is called interference of waves.

Constructive Interference

Phase difference between two waves = 0, 2π, 4π
Maximum amplitude = (a + b)
Intensity ∝ (Amplitude)2 ∝ (a + b)2

In general, amplitude = √a2 + b2 +2abcos φ

Destructive Interference

Phase difference between two waves = π, 3π, 5π

Minimum amplitude = (a ~ b) = Difference of component amplitudes.

Intensity ∝ (Amplitude)2

∝ (a – b)2

A vibrating tuning fork, when rotated near ear, produced loud sound and silence due to constructive and destructive interference.

Beats

When two sound waves of nearly equal frequencies are produced simultaneously, then intensity of the resultant sound produced by their superposition increases and decreases alternately with time. This rise and fall intensity of sound is called beats.

The number of maxima or minima heard in one second is called beats frequency.

 

[The difference of frequencies should not be more than 10. Sound persists on human ear drums for 0.1 second. Hence, beats will not be heard if the frequency difference exceeds 10]

Number of beats heard per second = n1 – n2 = difference of frequencies of two waves.

Maximum amplitude = (a1 + a2)

Maximum intensity = (Maximum amplitude)2 = (a1 + a2)2

CBSE Class 11 Physics Notes Waves and Sound

For loudness, time intervals are

Stationary or Standing Waves

When two similar waves propagate in a bounded medium in opposite directions, then due to their superposition a new type of wave is obtained, which appears stationary in the medium. This wave is called stationary or standing waves.

Equation of a stationary wave

CBSE Class 11 Physics Notes Waves and Sound

Nodes and antinodes are obtained alternatively in a stationary waves.

CBSE Class 11 Physics Notes Waves and Sound
  • At nodes, the displacement of the particles remains minimum, strain is maximum,pressure and density variations are maximum.
  • At antinodes, the displacement of the particles remains maximum, strain is minimum, pressure and density variations are minimum.
  • The distance between two consecutive nodes or two consecutive antinodes = λ/2.
  • The distance between a node and adjoining antinode = λ/4.
  • All the particles between two nodes vibrate in same phase. particles on two sides of a node vibrate in opposite phase.
  • n consecutive nodes are separated n by ((n -l)λ/2) .

Vibrations in a Stretched String

Velocity of a transverse wave in a stretched string.

CBSE Class 11 Physics Notes Waves and Sound

Where,T is tension in the string and m is mass per unit length of the string.

Fundamental frequency or frequency of first harmonic

CBSE Class 11 Physics Notes Waves and Sound

Frequency of first overtone or second harmonic

n2 = 2(v/2l) = 2n1

Frequency of second overtone or third harmonic

n3 = 3(v/2l) = 3n1

n: n: n: … = 1 : 2 : 3 : …

Organ Pipes

Organ pipes are those cylindrical pipes which are used for produe musical (longitudial) sounds. Organ pipes are of two types

  1. Open Organ Pipe Cylindrical pipes open at both ends.
  2. Closed Organ Pipe Cylindrical pipes open at one end closed at other end.

Fundamental Note

It is the sound of lowest frequency produced in fundamental note., vibration of a system.

Overtones Tones having frequencies greater than the runoamen note are called overtones.

 

Harmonics When the frequencies of overtone are integral multiples of the fundamental, then they are known as harmonics. Thus note of lowest frequency n is called fundamental note or first harmonics. The note of frequency 2n is called second harmonic or first overtone.

Vibrations in Open Organ Pipe

CBSE Class 11 Physics Notes Waves and Sound

fundamental frequency or frequency of first harmonic

n1 = (2v/l)

frequency of first overtone or second harmonic

n2 = (2v/2l) = 2n1

Frequency of second overtone or third harmonic

n3 = (3v/2l) = 3n1

n1 : n2 : n3 : …. = 1 : 2 : 3 …

Therefore,even and odd harmonics are produced by an open organ pipe.

Vibrations in Closed Organ Pipe

CBSE Class 11 Physics Notes Waves and Sound

Fundamental frequency or frequency of first harmonic

n1 = (v/4l)

Frequency of first harmonic or third harmonic

n3 = 5(v/4l) = 5n1

n1 : n2 : n3 : … 1 : 3 : 5 : …

Frequency of second harmonic or fifth harmonic

n3 = (3v/2l) = 3n1

Therefore only even harmonics are produced by a closed organ pipe.

End Correction

Antinode is not obtained at exact open end but slightly above it. The distance between open and antinode is called end correction.

It is denoted by e.

  • Effective length of an open organ pipe = (l + 2e)
  • Effective length of a closed organ pipe = (1 + e)
  • If r is the radius of organ pipe, then e = 0.6 r

Factors Affecting Frequency of Pipe

  1. Length of air column, n ∝ (1/l)
  2. Radius of air column, n ∝ (1/r)
  3. Temperature of air column, n ∝ √T
  4. Pressure of air inside air column, n ∝ √p
  5. Density of air, n ∝ (1/√ρ)
  6. Velocity of sound in air column, n ∝ v

Resonance Tube

Resonance tube is a closed organ pipe in which length of air coluDf can be changed by changing height of liquid column in it.

CBSE Class 11 Physics Notes Waves and Sound

Melde’s Experiment 

In longitudinal mode, vibrations of the prongs of tuning fork are the length of the string.

CBSE Class 11 Physics Notes Waves and Sound

In transverse mode, vibrations of tuning fork are at 90° to the length of string.

CBSE Class 11 Physics Notes Waves and Sound

In both modes of vibrations, Melde’s law

p2T = constant, is obeyed.

Characteristics of Musical Sound

Musical sound has three characteristics

(i) Intensity or Loudness Intensity of sound is energy transmitted per second per unit area by sound waves. Its SI unit is watt/metre2. Intensity is measured in decibel (dB).

(ii) Pitch or Frequency Pitch of sound directly depends on frequency.

 

A shrill and sharp sound has higher pitch and a grave and dull sound has lower pitch.

(iii) Quality or Timbre Quality is the characteristic of sound that differentiates between two sounds of same intensity and same frequency .

Quality depends on harmonics and their relative order and intensity.

Doppler’s Effect

The phenomena of apparent change in frequency of source due to a relative motion between the source and observer is called Doppler’s effect.

(i) When Source is Moving and Observer is at Rest When source is moving with ‘velocity towards an observer at rest, then apparent frequency

CBSE Class 11 Physics Notes Waves and Sound

(ii) When Source is at Rest and Observer is Moving When observer is moving with velocity VO’ towards a source at rest, then apparent frequency.

CBSE Class 11 Physics Notes Waves and Sound

(iii) When Source and Observer Both are Moving

(a) When both are moving in same direction along the direction of propagation of sound, then

CBSE Class 11 Physics Notes Waves and Sound

Transverse Doppler’s Effect

(i) The Doppler’s effect in sound does not take place in the transverse direction.

(ii) As shown in figure, the position of a source is S and of observer is O. The component of velocity of source towards the observer is V cos θ. For this situation, the approach frequency is

CBSE Class 11 Physics Notes Waves and Sound

f ‘ which will now be a function of θ so, it will no more constant.

Similarly, if the source is moving away from the observer as shown above, with velocity component Vs cos θ then,

CBSE Class 11 Physics Notes Waves and Sound

(iii) If θ = 90°, the Vs cos θ = 0 and there is no shift in the frequency.

Thus, at point P, Doppler’s effect does not occur.

Effect of Wind

CBSE Class 11 Physics Notes Waves and Sound

If wind is also blowing with a velocity w in the direction of sound, then its velocity is added to the velocity of sound. Hence, in this condition the apparent frequency is givenby

Applications of Doppler’s Effect

The measurement of Doppler shift has been used

  1. by police to check overspeeding of vehicles.
  2. at airports to guide the aircraft.
  3. to study heart beats and blood flow in different parts of the body.
  4. by astrophysicist to measure the velocities of plants and stars.